A spatial span task with routes: a marker walks a route over a grid map with landmarks, one neighbouring square at a time, and the participant taps the route back in order. Routes grow by one square until both routes of a length are wrong. Every map and route is generated from a seed.
Configure parameters and run an interactive preview exactly as participants will experience it. No data is recorded.
Adjust parameters below, then start the preview on the right.
Include practice trials
Shown with feedback before the main task
Task parameters
Default 2, as in the standard Corsi procedure (Kessels et al., 2000).
Default 9 (Kessels et al., 2000). At most half the squares of the map (12 on this map).
Default 2 (Kessels et al., 2000). The next length follows when at least one route of a length was right; the task stops when all were wrong.
Default 5 × 5 (our choice; no published grid size).
Default 500 ms, as each block is lit in eCorsi (Brunetti et al., 2014).
Default 500 ms: one square per second, the Corsi rate (Kessels et al., 2000; Brunetti et al., 2014).
Drawn icons (tree, fountain, tower, house, flag, bridge) as reference points; default 4 (our choice).
Default none (our choice; the Corsi procedures set none). A route not finished in time counts as an omission and as wrong.
With feedback on every tap. Default 3 (eCorsi: three practice sequences, Brunetti et al., 2014).
Default 3 squares (eCorsi, Brunetti et al., 2014).
Empty: each participant gets a new map and new routes, and the seed they were drawn from is stored with the result. The same seed gives every participant the same map and routes.
The span procedure of the Corsi block-tapping test (Kessels et al., 2000) applied to routes on a map, as the Walking Corsi Test applies it to paths walked on the floor (Piccardi et al., 2008). Every step goes to a neighbouring square and a route never crosses itself, so routes are likely easier to hold than Corsi sequences of the same length (path configuration matters: Busch et al., 2005; Parmentier et al., 2005); expect longer spans than on the Corsi test and check for a ceiling at the longest route. About 3 min with these settings (assuming a span of about 6). Outputs: span, routes tapped correctly, total score (span × correct routes), squares tapped in the right place, median time to the first tap and between taps; each trial stores the map, the route, the taps and the time of every tap.
This is a researcher preview. No participant data is recorded.
Simulated participant view
A spatial span task with routes: a marker walks a route over a grid map with landmarks, one neighbouring square at a time, and the participant taps the route back in order. Routes grow by one square until both routes of a length are wrong. Every map and route is generated from a seed.
No data is recorded
A square map (5 × 5 by default) fills the width of the screen, with a few landmarks drawn as dark icons (tree, fountain, tower, house, flag, bridge) told apart by shape, not colour. The marker lights up one square at a time; then every square is a button. A tapped square lights up briefly; in practice it turns green or red, and the route is shown numbered afterwards.
For a spatial span measure with routes instead of scattered locations, as in the route and topographical memory literature (Walking Corsi Test), and as practice for the route tasks of selection tests. The span procedure is the standard Corsi procedure (Kessels et al., 2000), so span and total score are defined as there. Maps and routes are generated, so sessions can use new routes (no seed) or one fixed form (a set seed).
Not a normed test and not a substitute for the Corsi test: routes along neighbouring squares never cross themselves and are likely easier to hold than Corsi sequences of the same length, so spans are not comparable with Corsi norms. Not a quick EMA probe: the span procedure takes a few minutes and its length depends on performance. Not a navigation test in large-scale space (the map is seen from above).
Keep the defaults for the standard procedure: routes of 2 to 9 squares, two per length, the next length when at least one route of a length was right, stop when both were wrong; 500 ms per square and 500 ms between squares (one square per second); three practice routes of three squares with feedback. Leave the seed empty for a new map and routes per participant and session, or set one to give everyone the same form. If many participants reach the longest route, raise it (up to half the squares of the map) or use a larger map.
The span procedure is the Corsi procedure of Kessels et al. (2000): both routes of a length are always given, the next length follows when at least one was right, and the run stops when both are wrong or after the longest length. Span is the longest length tapped correctly; the total score (span × correct routes) also counts the routes tapped correctly on the way. A route is right only when every square is tapped in order; squares in the right place give partial credit, as in partial-credit scoring of span tasks (Conway et al., 2005). Unlike Corsi sequences, every step goes to a neighbouring square (no diagonal steps), no route crosses itself, and no more than two steps in a row go the same way, so a route cannot be a single straight line. Path length, crossings and angles change how hard spatial sequences are (Busch et al., 2005; Parmentier et al., 2005): expect longer spans than on the Corsi test, and check for a ceiling at the longest route. The map and its landmarks stay the same for the whole run, as the Corsi board does. Times are taken at touch-down from the moment the marker has left the last square; this timing has not been validated on real devices. The task has no norms; compare groups or sessions within a study.
Each run of this task records how its times were measured and the conditions of the session, such as screen brightness, battery saving and interruptions. Runs with possible problems are flagged on the Quality tab and in the export.
How SMAAT times cognitive tasksAdd Route Memory to your ESM study on SMAAT — free to get started.